DDave 14mm Arizer EQ/VTower Mod Kit V2
Each Complete Kit includes:
The Original DDave Adapter - 14mm F/F that accommodates a screen. (Plus 6 screens).
An 14mm Clear Borosilicate glass wand + 3 tip basket SS screens
An 14mm Tall DDave adapter. Like cyclone bowl with fixed screen and without draw restriction (for a limited time).
A test tube clamp - the perfect holder for a hot adapter!
One Whip Tube - 2.5 feet long
One Whip Water Tool Adapter (your choice at time of order, 14mm or 18mm).
**** Now includes 5 BeesWax Beads (at no additional cost).
BeesWax - Your No-Stick Glass Solution: Use optional. There have been some who have reported their ground glass getting stuck together. Regardless of reason, beeswax can help and Ddave loves to help! So, included in your kit at no extra charge will be 5 Free BeesWax Beads. To use them, rub gently on your “male” ground glass joints. You don't need much as a protective layer to help prevent glass-lock. (If you find it difficult to apply, slightly heat the male glass joint before applying).
Please note, these wands do not accomodate the internal screens you've seen described in the DDave Mod information online. This is a later update to the DDave Mod which was found to be an improvement over the previous release, as your product sits even closer to the heater than if housed inside the wand itself. See the below instructions for suggested operating methods.
There are two methods to using the new DDave Mod. Power and Smooth. Each are described below. Preheat your glass adapter of choice for 10-15 minutes at your desired temperature before beginning your sessions!
Power Session Mode: In this mode, you will pack the basket screen with your product, lightly tamping it down so it stays in place when you insert the wand into the DDave Adapter. This works with both the DDave Short Adapter and DDave Tall Adapter. This method can be directly compared to the "Elbow Pack" method mentioned when using the Arizer Elbow and associated basket screen. For ease of loading, simply vacuum up the herb by drawing on the whip then tamp down when the basket screen is filled to desired level. Then insert in a preheated tower / DDave adapter and enjoy your session.
Smooth Session Mode: In this mode, you will use either the DDave Short Adapter or the DDave Tall Adapter to hold your product. Ensure your product quantities are of volume so that the product moves freely within the adapter during an inhale. Load product directly into the DDave Adapter. A slow draw will give you an lighter hit, which will be a bit more flavorful. You will also get more of these light hits per product load. If you hit it a bit heavier, you will obtain results a bit closer to the Power method above, as you will force your product to compress itself into the basked screen while drawing.
Tall Adapters: Included for lighter, more flavorful sessions. Herb will be approx same distance from heater as with stock Cyclone bowl, but without the wobbly center screen and without the center ring restricting airflow.
Wand Auto-Pack: Load the 14mm Short adapter with your herbs, insert wand, inhale sharply through whip or water tool... Watch the herbs raise and "pack" themselves into the wand's basket screen for perfect tamp and awesome extraction. Continue your draw at normal speed after the auto-pack occurs.
Don't forget to use the included Clamp to remove and/or hold any hot pieces of glass included in the kit during your session... loading or unloading product. The clamp can be left in place during a session, even if clamped to a hot DDave Adapter, it does not become hot enough to burn. However, to avoid accidents, be careful of bumping into the clamp and possibly knocking over your vaporizer.
Heat Disclaimer: During use of the DDave Mod, as with any heated vaporizer components or addons, care must be taken to avoid being burned! We all have different tollerances, to heat (and other things), so using personal best judgement is advised and properly warning guests of this would probably be appreciated as well. Glass gets hot!
Questions/Concerns/Comments/Feedback: My Friend. It is my hope that this kit helps you obtain the results you desire from your vaping sessions. Please feel free to contact me at DdaveMod@Gmail.com or by using the Contact DDave Option at www.DdaveMods.com.
Defective Pieces: While I've made efforts to maintain quality control over suppliers and pieces of these kits, if you've received a piece you believe is defective, please contact me. I would ask for a description of the issue seen and a pic or two showing the problem. I'd like the opportunity to not only discuss the issue & remedy with you, but also to feed this information back to my suppliers so I can reinforce their quality control practices. While glass is hand made and subject to subtle differences, I do hold my suppliers to high standards. I wish to provide you a kit that will serve you well for many years to come.